Sunday, February 21, 2016

Coming soon....if I can ever get the stupid picture uploader to sync with my 4 million devices that separately contain all the pictures needed to show the process for creating your own DIY Rustic Plank Wood Floor...and the most important part- around 50 cents per square ft!!!

Sunday, February 14, 2016

Visit our Facebook page for a tiny glimpse of things to come!


Easiest and Cheapest DIY Barn Door Ever- Part 2: Making the Door


Once we found our bargain sliding barn door hardware (Read Easiest and Cheapest DIY Barn Door Ever- Part 1 if you missed it), we had to figure out how we were going to make this great big rustic looking barn door I wanted. We planned our door to be 55" wide and 8' tall. We picked 8' tall because had the room for it on our wall, and we wouldn't have to cut the wood...still trying to keep this project simple and easy.

Tongue and Groove Revelations

Again, I googled "DIY Barn Door," and found tons of helpful blogs, tutorials, instructions, and ideas on how we could do this. Most of these included gluing several pieces of 1"x6" pieces together and then clamping, tying, or using any method to get these pieces to stick together, and letting them dry this way. This seemed like a total pain to me, and then I had a stroke of genius: tongue and groove wood. If you google and pintrest what you want to do until you are blue in the face, you will come up with the best way for you to do it before you actually lose your sanity! So, this little idea is what makes this the cheapest and easiest way to create a big, beautiful, rustic, expensive looking barn door....without spending that much money!!

We were giddy when we got to Home Depot and saw 1) how nice the tongue and groove wood looked (and it is actually very sturdy once put together); 2) how light it would be compared to using other types of wood (we didn't want it to be super heavy on the track); and 3) how EASY this was going to be!!!! Mike was looking forward to a project for once, instead of dreading what landmines were waiting for us along the way.

Short and Simple List: Materials for building a Tongue and Groove Barn Door

Here is what we used to make our barn door:

- 10 pieces of tongue and groove pine, 8 ft tall (or however tall you want it- it comes in 6 ft, 8 ft and 12 ft at Home Depot. We used this one, which I was estatic to find because it  was about $5 per board: I also like this board because it has a beadboard-like pattern on one side.)

- 1x6 Trim pieces (For our design, we used 2- 1"x6"x8" pine boards, and 1- 1"x6"x12" pine board, which can be found at Home depot here:, and here:

-Wood glue (We used:

- Clamps to attach the trim while it dries (Harbor Freight has good ones cheap: This photo shows various random clamps we had to use:

- Paint

Tools Needed:

- Saw- if you need to make any cuts. If you don't want to make the cuts yourself, Home Depot and other stores will make simple cuts for a minimal charge. (we used our table saw)

*Note: If you have the store cut your wood for you, make sure to cut a groove off one board and a tongue off another board so that you can use those pieces for the sides of the door.

Assembling the Door...Also Short and Simple

It took us only 2 days to make the door, and the only reason it took that long was because of the time it took to let the trim dry on the door. The glue says it sets within 60 minutes, and cures within 24 hours. We wanted to play it safe and waited the full 24 hours to move the door.

First things first, we had to have a place to assemble this massive door. Mike used two wooden sawhorses we have had for a while, and we have gotten a TON of use out of them. If you do a lot of projects (or plan on doing a lot in the future), you can make a small investment and get two of these for less than $40: We use scrap pieces of plywood over them to make a table. But, any flat surface will do- just make sure you have enough room for the size of the assembled door, and that its in a place where you can leave it for a couple of days without needing to move it. We also put plastic under our makeshift table because the glue can drip a little.

Our makeshift sawhorse table:

When we got our materials home and carried it up our TWO flights of stairs (this part always sucks), we laid the pieces of tongue and groove wood out on our sawhorse table to see what side we wanted to use and what it was going to look this:


Envisioning how our trim would look when it was finished:
The other side of the wood has lines in it, like beadboard (the pictures on the Home Depot website show the design). I wanted that side to face the hallway when the door was closed so that side of the door would have a little character.

To make the sides of the door look like normal pieces of wood, Mike cut the groove off one board and the tongue off another board. We laid these pieces on each end before we started gluing the boards together.

The next step was to put glue in the groove on the board, one board at a time, and secure it into the tongue on the next board. This was super easy with two people- having one person on each end of the boards helps line them up easier, and then pressing them together is easier too. We found after a couple of boards that if we stopped the glue about 6 inches from each end, the glue wouldn't drip out at the ends.

It took probably 10-15 minutes to do this, and then we were done! We let the door dry overnight.
Mike tied it overnight to make sure it stayed in place (I don't think this is necessary for tongue and groove wood, but it's good to make sure it stays super tight):
Adding Trim to the Door

After the glue on the boards dried for 24 hour, we added the trim. If you look at barn door designs online, your brain might explode from all the different options you have. Some people like trim around the edge and one long, diagonal piece across the middle of the door (that was a little more country than rustic for my taste). Other people get super creative (and complicated) with herringbone wood designs on the front of the door. In keeping with my quick, easy and simple plan, this is the design we decided on for our trim- trim around the sides and one board across the middle:
So, we had two pieces of 1"x6"x8' pine boards for each side of the door. Mike glued those, put them in place and clamped them down to let them dry:

In the meantime, he measured between the two side trim pieces and cut 3 pieces out of our 1"x6"x12' board for the top, bottom and middle pieces. He waited until the side pieces dried for a while so that they wouldn't move when we added these piece in the middle. Once those were glued down, he clamped them and let all of the trim dry overnight.
That's it! Our barn door was built!! (Or, at least we thought that was it- more on that later....but as long as you have your measurements right and you've account for the height of the track, your barn door would be finished at this point!)
Mike painted 2 coats and then the door was really done:
So all these materials together cost us around $80 to make a 55" wide, 8 ft tall, solid pine wood barn door- an AMAZING deal compared to other doors I have seen ranging around $300 and up (and you won't get one this size for even that amount of money).
We found this beautiful doorhandle on Ebay to add when we're completely finished- keep in mind that you need a very large handle for a door this size. This handle is 8" tall.
Now comes the real fun (sarcasm this time)...hanging the track and this massive door.
Easiest and Cheapest DIY Barn Door Ever- Part 3: Hanging the Hardware and Door (Coming soon....I promise)


Saturday, February 13, 2016

Easiest and Cheapest DIY Barn Door Ever- Part 1: Planning

Before we even moved into our house, a little over a year ago. There were a few things I knew I HAD to have. Otherwise, what would be the point of having a house??

For example, the first thing I ever purchased for my house (before I even closed on it) was a HUGE hammered copper apron farm sink. I saw it at Home Depot and I HAD to have it. It was a great investment....but it's really testing my patience because its still in the fancy wooden crate it arrived it (which I was super impressed with, by the way), in the bottom floor of our townhouse with all the other things that haven't been unpacked yet because there is no place to put them yet. Yes, I know I've lived here for over a year, but don't judge me. Living through a full-on renovation of a complete home is nothing like moving and unpacking all your stuff. There is no reason to unpack anything until we have a place for things because otherwise we will just be moving things from room-to-room all the time. So, we live on Floor 2, we started renovations on Floor 3 (so nothing unpacked up there), and Floor 1 has a garage and bonus room full of things we have no place for yet.

Anyway, back on (barn door) track- another thing I knew I MUST have was a wooden sliding barn door. I had to have it so much that I planned a room around it. It might seem obvious, but you have to plan enough room for a door to be able to slide open. Since our house was built in 1991, everything was very compartmentalized - not like the open floor plans that are all the rage now. We are doing our best to open up the floorplan here (and I will have plenty of posts about how we are managing that in a 15-ft wide, 3 story building), but at some point you have to stick with what you've got.


The perfect place for this in our house was our master bedroom because: 1) it has vaulted ceilings- plenty of room to put a tall door and still have room for the sliding door hardware to go above it (and have even more room above it on the wall so it didn't look crammed in- the rest of the ceilings in our house are only 8' so the door would have to be smaller if we did it in another room); 2) There was enough wall space for the door to be able to slide open all the way to one side (when you're planning this, make sure there is enough room on the wall for the door to be able to slide all the way open without hitting any obstructions, and that there is enough length on the wall for the entire door to go over- keep air vents on the wall in mind!!). There is literally nowhere else in our house a door like this would fit, so it is important to plan well before you dive into this project.

Our door opening was around 43", and we decided to do a 55" door. How did I come up with 55" wide? I knew I wanted the door to cover the opening, but even more than that- we've had a lot of complicated projects lately and I wanted this one to be simple. So I found the 1"x6" planks of wood I wanted to use at Home Depot, and decided that 10 is a good, simple number. 5.5" wide x 10= 55," but you can make a sliding barn door any size you want. We just had to make sure there was more than 55" on the left side of the doorway (the direction I wanted the door to slide) so that the door could open all the way. We have about 30" extra to the left of the 55" that the door would open.
Another option if you have a more central door opening on a wall is to do two smaller barn doors that come together in the middle- in this case we could have done two 27.5" (5.5" x 5) that came together in the middle. I didn't have enough room on the right side of the doorway to do this (I originally planned it this way and it failed, if you couldn't already tell).

Sidenote: Another thing that might be obvious to some people, but maybe not to someone new to construction, DIY, projects (and specifically new to the use of one by whatever's) is that wood is not the actual size it says it is. 1" x 6" really means 0.75" x 5.5." I cannot explain this to you. I have just come to accept the fact that nothing is what it says it is when it comes to lumber and millwork, and I have memorized the crazy way this is done, plus I bring a measuring tape with me when I buy it to avoid mishaps and lots of tears in my chardonnay glass later. I'm sure Google can better explain this, but it won't ease my frustration so I'm not worrying about WHY??! anymore.


The first step I took in my barn door endeavor was to find the sliding door hardware. I searched for a long time. I was initially SHOCKED by the price of a set at normal stores. So, as I have learned to do, I typed "DIY sliding barn door hardware" into a search. This method works for anything that you need a solution to: typing "DIY" and whatever you need to tackle into Google together WILL give you what you are looking for. Probably many. In the words of Barnaked Ladies, "It's all been done before..." and someone has probably blogged about it.

There are many ways to make your own hardware. Some looked easier than others.....but by the time I added up the materials needed to make a set (and I wanted two sets, of course- because, as Mike would point out, I always have to do everything BIG and be difficult), I figured there had to be somewhere I could buy these things pre-made.

Enter my trusty, old friend, Ebay. The standard size for the hardware seemed to be 6ft, and of course they come in many other sizes. After an intensive search, I was able to buy 2-6.6 ft sets of hardware for $110 and free shipping- TOTAL!! There are a ton of Ebay listings for this hardware, but here is one to get your search started:

This is the set I purchased and the ends of the track are flat, so they are super easy to put together if you do need more than one set, or longer than 6 feet.

 So, once you have planned your door location and size, and found your hardware, you can move on to the fun part: Making the door. (I'm usually being sarcastic, but this time I actually mean it- it's fun! Especially compared to some of the pain-in-the-ass projects we have suffered through before)

See the next post: Easiest and Cheapest DIY Barn Door Ever- Part 2: Making the Door

Welcome to Our World...

Hi, welcome to my crazy world. I'm a lawyer-turned DIY addict with a little bit of project A.D.D. I was happily ignoring DIY blogs and Pintrest (because I knew I would get too many ideas and not know when or where to stop), when my friend would not shutup until I looked at her favorite DIY blog. The inevitable happened, and I wanted to start making everything I read about IMMEDIATELY. I started out small, refinishing a wooden dresser that was in my boyfriend's family for about 50 years and looking very un-loved. I found that tearing things apart and putting them back together all pretty was VERY therapeutic for dealing with my stressful work...sanding layers of ugly abuse off old furniture was especially stress-relieving. That was almost 5 years ago, and it's been all downhill (from my boyfriend's point of view- uphill from mine:) from there. I started looking at blog after blog, starting one project after another....I was hooked. Finally, I had to buy a house to feed my DIY addiction. Then I finally gave into Pintrest (obviously!- it's so awesome!) when I "needed" new ideas for the house we were about to buy. Thanks to this little website, we have about 3 million things on our to-do list, and we can't see the light at the end of the tunnel AT ALL yet.

That brings us to the middle of a humongous renovation of a 3-story, 2,000 square foot townhome. I'm not really sure how this happened so fast, but good days and bad, we're loving the excitement of it all. It's amazing to see something beautiful and well-made when you finish a project. The satisfaction that comes from making something and seeing things transform is boyfriend, Mike, has even come around and began to really enjoy seeing his finished work.

We live on a tight budget (thanks a lot, student loans), and most times we have to be creative with how we tackle a big this house thing were working on :) With a lot of patience (and wine, on my part), we're always able to figure it out.

This blog started out with several other names I had thought of, but never really organized enough to publish it. It came to be known as Over-Inspired due to the fact that I love to watch a DIY show, get up off the couch when the episode is over and take a hammer to my walls...exactly the way I just saw them do it on TV! This method has cost me a lot of money at times, and I would suggest actually researching what you want to do before completely tearing your house apart! Anyway, we hope our journey inspires you and helps you figure out the best way to tackle your projects- big and small!

- Chantel and Mike